Tunnel and Metros

http://www.applechemie.com/

AC-CURE-(S)-Its a wax based curing compound

When Sprayed on fresh concrete it forms a continuous film and cover the concrete and prevents evaporation of water from it The water added during the concrete mixing is sufficient for the complete the hydration of cement and development of full strength of concrete. AC Cure (S) can prevent drying shrinkage cracks. Water curing may be reduced. The product conforms to BS: 7542 l ASTM-C-309

AC-SPRAY SET-163

  • Alkali-free set accelerator for wet-mix sprayed concrete
  • Quick setting properties allow thicker overhead layer in the single application. 120-200 mm thickness)
  • It allows high workability and rapid progress of work
  • Unique liquid formula allows easy handling efficient addition at the nozzle of a spray gun
  • Environment-friendly
  • Impart early higher strength and control, decrease in final strength which normally in case of accelerators.
  • Alkali-free nature of product improves work environment & the safety.

AC-CEMENT-CAPSULE

  • It is a Cementitious non-shrink grout designed for the anchoring of rebar or dowels in concrete,
    masonry and rock. Simple and economical
  • Easy to install
  • Easy handling and storage
  • Reduces installation time and cost
  • No product mixing on site
  • No special tools and equipment required High early strengths
  • Thixotropic mix
  • Stable water /cement ratio
  • No toxic emissions or fumes and environment friendly
  • No Calcium Chloride

AC-CABLE-GROUT

  • Pre-packed, Non-shrink Cementations Grout Admixture for Post Tensioned Cable As per
    ASTM C-827-01A, BIS 110 part 1 1985 and MORTH Appendix Sec 1800/III Gaseous positive
    expansion of the Grout compensates for the Shrinkage and settlement in a plastic paste of cement.
  • Makes Grout impermeable
  • Very strong and durable
  • It does not contain chlorides/nitrates/ sulfides
  • Compatible with OPC

AC-MOULD-KOTE

  • Mold release Agent in emulsion form
  • Increases the life of formwork.
  • It is a Green building product.
  • Leaves no stains on concrete after demoulding.
  • Allows easy demoulding of forms.
  • Allows efficient adhesion of forthcoming plasters, mortars and paints.
  • No dirt sticks on a surface after its drying.
  • Coated shuttering surface remains clean and free from remnants of concrete and cement splashes after
    demoulding. The bonding strength of concrete remains unaffected

AC-POLYSEAL

  • Recommended for sealing of expansion joints in movement joints. Conforms to IS 12118
    (part 1 81 2)- 1987, BS 4254 - 1983, BS 5212 - 1990
  • Easy to use and Economical
  • Excellent adhesion with old and new concrete
  • Non- sagging in vertical and overhead joints
  • Good chemical resistance and permanently elastic

AC-FLEX-CL

Carbonation protection coating for a portion of old street, new bridge.
Works Solvent free, non-toxic, safe and noncorrosive.
Highly carbonation resistant, elastomeric, nonstick, good binding, clean and seamless membrane coating, maintains original concrete breathing capacity.
Solar and UV resistant coating.

AC-MENT-BV-430-AM6

  • Super Plasticizer for all types of concrete works The Product Confirms IS-9103-1999. It gives:
  • Excellent pumpability, easy placement, and better finish.
  • Higher strength without an increase in cement content
  • Improved cohesion and less risk of shrinkage cracks.
  • Higher durability & higher impermeability No risk of reinforcement corrosion as the
    product is chloride free.
  • No side effects on concrete or steel

POLYUREA

  • Fast cure, short downtime, no sagging.
  • Excellent Physiochemical Properties.
  • Bondable and paintable to various kinds of substrates.
  • Ambient insensitive, good thermal stability.
  • 100% Solids, No VOC's, Odorless, No Toxic Vapors.
  • Good resistance to a wide range of chemical attack.
  • Excellent Abrasion resistance and Impact resistance.
  • good durability and color stability
  • Seamless, flexible, slick and non-porous

AC-RAIL-GROUT

  • Fast Setting, High Strength, Multipurpose, Nonshrink Cementitious Grout)
  • Easy to mix and install
  • It has a self-level property
  • Excellent bonding with concrete
  • High initial and final strength
  • Good pourability and workability
  • Bears high static and dynamic forces
  • Protects deterioration of reinforcement due to corrosion
  • It has excellent weatherability

AC-DUR-SBA(G)


  • Segment bonding adhesive for joining of bridge segments. As per ASTM C-881, BS 6319 (part IV)
  • Meets the International 8L National standards (FIP, BS, ASTM etc.)
  • It has a high initial strength and ultimate strength.
  • It has high scratch hardness, excellent adhesion and high abrasion resistance.
  • Excellent acid, alkali, salt and detergent resistance.
  • Most recommended for segmental construction of bridge and flyover 










AC-LOC-FIX


Hydrophilic Grout for Sand Stabilization

Special Product under Development .You ask, and we will design and deliver. Constant innovation is our work style



Comments

Post a Comment

Popular posts from this blog

Concrete Curing Compound

Curing is essential for the hydration of cement in concrete making. So, to maintain required moisture content, come precautions are applied. Concrete curing compound is a compound which helps to prevent the loss of moisture content from the concrete. So, concrete is properly cured which results the full development of strength of concrete. Types of Concrete Curing Compounds ·          Synthetic Resin Concrete Curing Compound Synthetic resins will seal the concrete by forming membrane. If we want to provide plastering, the membrane can be removed by washing it with hot water. ·          Acrylic Concrete Curing Compound Acrylic is made of polymers of acrylic acid. It also seals the concrete in good manner. It is having property of adhesion to the subsequent plaster. No need to wash the surface of acrylic with hot water if we want to provide plastering. ·      ...
Read more

Materials are used for road construction

Image
Road consist of basically 4 layers: Sub-grade: The sub-grade material should be clean and free from organic matter and should be able to be compacted by roller, to form stable sub-base. The material should have the following characteristics: ·          Well graded, uniformity coefficient (D60/D10) should not be less than 3. ·          Fraction passing sieve #200 shall not be greater than 2/3rd of the fraction passing sieve #40. ·          Should have a L.L not greater than 25%. ·          P.I not greater than 6 ·          CBR should not be less than 25. ·          In coarse grain, aggregate retained by #10 sieve, %age of wear shall not be greater than 5%. ·          The maximum dia...
Read more

DESIGN PROCEDURES FOR A BUILDING FOUNDATION

Good design must not only be safe but must aim to save construction costs, time and materials. The following procedures should help to achieve this and an ‘educated’ client will recognize the importance of funding this work with a realistic fee. 1. DECIDE THE LOCATION OF COLUMNS & FOUNDATION AND TYPE OF LOADS ACTING ON THEM On the building plan, the position of columns and load bearing walls should be marked, and any other induced loading's and bending moments. The loads should be classified into dead, imposed and wind loading's, giving the appropriate partial safety factors for these loads. 2. ESTIMATE ALLOWABLE BEARING PRESSURE OF SOIL USING GROUND INVESTIGATION REPORT From a study of the site ground investigation (if available), the strength of the soil at various depths or strata below foundation level should be studied, to determine the safe bearing capacity at various levels. These values – or presumed bearing values (from any standards or codes) in the...
Read more